xandr pixel
Skip to main content

Fix An Outdoor Leaky Faucet

An outdoor leaky faucet can be easy to repair, and you only need a few simple tools & patience. Here are a few steps to repair your dripping outdoor faucet.

Leaky Outdoor Faucet

There’s nothing quite so annoying as an outdoor leaky faucet, as you watch beads of water form, either quickly or slowly, and drop to the ground. A leaking outdoor faucet is more than an annoyance, however; in addition to the moisture that can build up next to your house, you also lose money with every drop of wasted water. Fortunately, a leaking outdoor faucet is easy to repair, and you only need a few simple tools and a little patience. The tools you need to gather before you start are an adjustable wrench or vise grips, a Phillips-head screwdriver, and a rubber washer. Here are some steps to take to fix that pesky leaking outdoor faucet:

Step 1: Turn off the water to your house

You can do this at the main water shutoff inside your house, typically located near the water heater, or at the street. The latter method requires a curb key, also called a water main key, which is sold at most home improvement stores. To use the curb key, open the cover to your water meter and insert the key at the notch inside the meter that controls the flow of water from the street to your house. Use the key to turn the notch clockwise about a half-turn, or until it won’t turn anymore.

Step 2: Drain The Line

Now that you’ve turned off the water to your house, you’ll want to make sure all the water is out of the line that runs to the outdoor faucet. Turn the valve of the faucet to the on position, and wait until the water has stopped flowing. If water continues to come out after about 15 seconds, check to make sure you have turned the water completely off.

outdoor faucet parts

Step 3: Fix the Broken Washer

After you’ve drained the faucet, you’re ready to get to the likely source of the leak: a broken or disintegrating washer. To reach the washer, it is necessary to take the faucet apart. First, use a Phillips-head screwdriver to remove the screw that secures the valve (the part that turns the water flow on or off). Pull gently to remove the valve, and set both the valve and screw aside.

Next, remove the packing nut (the thick nut about 1/2″ in diameter) by using your adjustable wrench or vise grips to unscrew the nut from the threaded part of the faucet; set this nut aside too. Finally, again using your wrench or vise grips, unscrew the larger hexagonal-shaped nut and set it aside as well. You should now be able to remove the faucet; you may need to gently but firmly twist the faucet while pulling to remove it from the house. At the end of the faucet is the washer that’s most likely causing your leak. Gently remove it (this may require the use of a flat-head screwdriver to nudge it out of place), and replace it with a new washer.

You’ve now fixed the leak, and the only thing left to do is to reassemble the faucet.

Insert the faucet back into the house, and screw the hexagonal nut back in place; use your wrench or vise grips to tighten the nut. Next, screw on the packing nut, and again tighten it with the wrench or vise grips. Finally, put the valve back onto the end of the faucet, and use the screwdriver to tighten the screw that holds the valve in place. Turn the valve clockwise completely to the “off” position, and then turn the water to the house back on. Check for any leaks. If water is leaking from somewhere other than the original leak from the spigot, be sure to tighten all the nuts until the leak stops.

Plumbing projects may seem intimidating, but fixing a leaky outdoor faucet is pretty simple. It will be worth the effort when you save money on water bills and save yourself the frustration of watching water drip all day long.

If you have a leaky outdoor faucet you simply cannot fix, don’t hesitate to call the PROS at Plumb Pro+!